Wednesday, March 14, 2007

cannon... a work in progress. Part 4

The back half has been turned down. You can also see the file mentioned earlier in the bottom left of the pic.








Here it is.









Just another view showing the button on the back. It didn't quite get rounded enough. Now that I did this one I've got some thoughts on how to make things go smoother.

As mentioned, use as large a spindle as you can. Reduce the epoxy use so that it's only as large as the smallest section. If possible, use wood caps or something that will not dig into the foam if the nuts tighten. Cut as close to the finished size as possible, make it "stair step" and cut the sections round as this balances it and reduces wobble and the mess.

The biggest thing that would help is to use a wood lathe with a support would be much better suited to turning foam then a metal lathe set up like this.

The only thing left is to drill a hole in the barrel, add the trunions, and the vent hole. After that it's all a matter of skinning it over. Wood glue works well, then you can apply polyester resin or bondo to form a hard shell. Smooth that, spot putty and then make a mold.

I'm debating if I should do another with the changes I mentioned above to improve the shape. Some sections are slightly out of round due to the wobble in the thin shaft.

more to come...

cannon... a work in progress. Part 3

The front half of the cannon is turned down. Basically it was just long boring work. Something I found out along the way, USE THE LARGEST DIAMETER SPINDLE AS YOU CAN. There were some vibration issues and "flop" at higher speeds, due to the length of the rod as well as it's thin 3/8" diameter. 1/2" would probably have been better, 3/4" better still. I think that's as thick as I could do without boring the headstock on the lathe out.




A little bit further along in the process. No, no action photos since I only have two hands. Another thing I realized is that I should have only used epoxy to the smallest diameter of the foam...that is, it doesn't shape as well with file cards so you'll have to use the file on it. If less is used in the only the center you can turn it quicker.





A close up of the end. if you look closely at the seams between the discs you can see they're raised, the result of the epoxy.








Here's some of the tools used, as well as a huge mess.










More to come...

cannon... a work in progress. Part 2

This is the basic plan, scaled up plans for a "miniature eighteen pounder" to what I felt would make a nice small cannon. Nothing too fancy here. In the background you can see the beginning of the shaping of the foam.








Here's a shot showing the initial smoothing out of all the rough cuts. You can also see that doing this makes a huge mess of very fine foam dust and chunks, depending on what kind of tools you're using. I guess I should mention what I'm using, huh? Primary tools are an auto body file, or a horse shoe file. It has large arched teeth and you'll be able to see it better in another pic later. Also a rasp, a file card and some drywall sandpaper. Open window screen type since it doesn't clog nearly as much. I said there was a bit of static, it's actually pretty cool to see the foam spinning and the small bits orbiting it, not flying off, but orbiting. It gets old fast since as soon as you touch them they stick to you instead.


More to come...

cannon... a work in progress. Part 1

So, as promised, the cannon build ....

I've turned foam before, back when I had no lathe. I did it with a large "U" shaped setup built out of 2x10. There was a large flat base with two uprights, one upright had a hole for a drill. I chucked up the threaded rod after fitting the drill into the large hole, the other end sat in a bearing. It worked OK, but not great as the drill kept falling out of the hole.

Now that I've got the lathe, I might as well use it right? If this cannon was an inch smaller in diameter I think I could have pulled it off over the bed. How can you turn a foam cannon that is larger then the mini lathe you have? Since you could turn several sections and glue them together, the real problem is how do you overcome the swing over the bed issue? You could build something like this.


Here we have the extended rear bed for a 7x12 mini lathe. It's just a piece of 2x10 with a piece cut off to form the support. Some shelf brackets and another piece of wood hold it in place. A hole was drilled to fit a small bearing that the threaded rod rides in. Yes, bench space has been exceeded. It's not really a smart idea to have it overhanging the bench like that. This will be fixed with the expansion of the shop in the somewhat near future.







The cannon itself is 21 discs cut out of pink insulation foam held together with 5 minute epoxy. A hole was drilled at the center of each disc to hold it onto a long piece of threaded rod. At the ends two nuts and as large a washer as I had on hand was used to clamp it together while the epoxy hardened.







You can see the washer here as well as the rough cutting of the foam.











More to come...

Cannon: step 0, err, -1

For some reason I can't get any pics uploaded here right now...so I'll hold off on adding cannon stuff.

I will say that there were a few issues that came up, but nothing too serious, and if anything it was a learning experience.

stay tuned.

Tuesday, February 27, 2007

some new props

Yep, now offering a 36" pipe wrench, a 12" crescent wrench, and a golf club.

Not too much new in the world here.

Working on a few props, including a 32" cannon that I'll probably detail the build here as it comes together. The barrel, I'm sure that there is a different term for it that I don't know, will be shaped out of XPS foam sheet. That's already been epoxied together with a threaded rod fit down the center. It will be mounted through the headstock of a lathe on an extension fit behind it and the far end of the rod will sit in a bearing. As with all foam, a rasp, file card, and dry wall screen will be used to shape it, all while the lathe runs in reverse to keep the speed down which should help prevent the foam from melting and tearing.

After the barrel is shaped, I'll coat it with wood glue to seal the foam, one or two coats is usually enough. Bondo "cut" with polyester resin will be applied, allowed to cure, then sanded and filed on the lathe. Finally, some spot putty to clean that up and make a nice glassy surface. Follow that up with some filler primer and we're ready to move on.

This is a private commission for display, but a mold will be made for casting fiberglass copies. Eventually I plan to make one that will fire pneumatically, perhaps marshmallows or NERF balls. I'm going to be making at least a 2 part brush-on 50 and fiberglass support shell. The plan is to only shape the last few inches of the barrel, then on casting to fit some PVC pipe into it.

To make the castings, both halves of the mold will have fiberglass matte laid up by hand, being careful not to cross the edge of the mold. When that has set, a bondo/polyester resin mix will be made, fiberglass tape applied to the seams, and the mold will be closed. I'll rotate the mold so the mixture bonds the two halves together. On opening the mold some final work will be needed, as is always the case, but this is mostly light sanding and touching up the seam with bondo, or spot putty, or both. The casting will be primed, then painted to look like either brass or cast iron.

The carriage will be another story.

For the immediate future I'll simply detail the cannon's construction.

Stay tuned for more on that....

...but first, Bucky Katt needs to get off my bench.

Monday, January 29, 2007

I'd just like to...

...go on record expressing my thanks for some of these folks.

Chensational's blog

puppeteers unite

Creaturiste's blog

Puppet 101

Snapdragon puppets


none of them actually helped me, but with the magic answer box here, a little bit of pattern making experience from my last "real" job making backpacks, and a lot of dumb luck I managed to pull off my first venture into something along the lines of puppet building. Three large sheet foam masks for a theater company.

You can see them by stopping by the site and having a look at the puppet samples.





WELCOME TO US

Hello from lovely snow covered Cleveland Ohio! Home to gray skies, snow, rain, and not too much else. OK, so there are some other things here. The Rock and Roll hall of Fame, the sports...all those damn sports, and well, I guess I covered everything.

Fine, there are some folks here trying to make some movies, folks doing special effects, hell, I guess there really is something going on here after all.

This will be a "behind the scenes" and commentary from my point of view on the FX scene here. Who am I? Why, I'm Tom. Don may chime in from time to time, but he's based down in Pittsburgh.

Welcome, now stop back soon when we have some more content.